èeštinaenglishpolski
Products  »  Pegatex SMS BICO
Pegatex SMS BICO

Pegatex®  SMS BICO - (spunbond/meltblown/spunbond) is non-woven fabric manufactured by the combination of Reicofil® 3 bi-component technologies spunbound (S) from polypropylene and polyethylene and meltblown (M) from polypropylene. The basic qualities of this type of non-woven fabric include excellent barrier qualities that are used to prevent liquid leakage in combination with the qualities of bi-component non-woven fabric. This type of fabric is used mainly in the applications of manufacturing of hygienic products (baby nappies, ladies hygiene products, incontinency nappies and towels).

Spunbond (S) part of SMS is manufactured by means of bi-component spunbond BICO Reicofil® 3 technology from polypropylene (core) and polyethylene (sheath). Polyethylene sheath of the individual filaments (continuous filaments) gives the resulting non-woven fabric specific qualities that include the following:

  • softness and very pleasant feel
  • excellent comfort qualities in contact with the most sensitive parts of human skin
  • higher elasticity
  • new quality for hygienic applications (baby nappies, ladies hygiene or incontinency products)
  • higher possibility of binding (polyethylene) with other materials for composite fabric
  • barrier qualities comparable with Pegatex SMS
  • These main advantages of Pegatex® SMS BICO non-woven fabric are present in all the applications where there is a direct contact with sensitive human skin with non-woven fabric. The main applications include baby nappies, ladies hygiene and incontinency nappies and towels.

    Difference you can feel!

    Pegatex® SMS BICO (bi-component spunbond) is manufactured by means of Reicofil® 3 technology on the equipment creating three layers of bi-component spunbond (SSS) and two layers of meltblown (MM) - SSMMS (the number of letters S and M marks the number of the individual layers).

     
    Basic surface density from 12g/m2 to 60/m2
    High barrier qualities and possibility of adjusting their intensity
    Possibility of adjusting surface density of the individual SMS layer
    Possibility of adjusting air permeability intensity
    High chemical stability

    Possible antistatic treatment

    Harmless to health

    Input raw material: meltblown (M): 100 % polypropylene
    spunbond (S): 50-70 % polypropylene and 30-50 % polyethylene
    Surface density: 12-60g/m2
    Max. roll width: 3,2 m
    Treatment: antistatic treatment
    Colour scheme: according to the customer’s requirements

    Applications:
    Hygienic applications


    PEGAS NONWOVENS SA
    68-70, boulevard de la Pétrusse
    L-2320 Luxembourg
    Luxembourg
    PEGAS NONWOVENS SA (société anonyme) is registered with R.C.S. Luxembourg under number B 112.044.



    PEGAS NONWOVENS s.r.o.
    Pøímìtická 86
    669 04 Znojmo
    Registration number: 254 78 478


    tel.: +420 515 262 411
    fax: +420 515 262 511
    e-mail: info@pegas.cz

    Incorporated by entry in the Commercial Register
    kept by the Regional Court in Brno, Section C, Entry 51762
    IMPORTANT NOTICE

    No action has been or will be taken in any jurisdiction other than the Czech Republic and Poland that would permit a public offering of the shares described in the Prospectus, or the viewing, possession or distribution of the Prospectus in any jurisdiction where action for that purpose is required. Accordingly, the shares may not be offered or sold, directly or indirectly, and this Prospectus may not be viewed, distributed or published, in or from any country or jurisdiction except in compliance with any applicable rules and regulations of any such country or jurisdiction.

    The communication of the Prospectus and the offer of the shares described therein in certain jurisdictions may be restricted by law and therefore persons into whose possession the Prospectus comes should inform themselves about and observe any such restrictions. Any failure to comply with these restrictions may constitute a violation of the securities laws of any such jurisdictions.

    THE PROSPECTUS MAY NOT BE ACCESSED BY PERSONS IN THE UNITED STATES, CANADA, JAPAN OR AUSTRALIA.

    THE SHARES DESCRIBED IN THE PROSPECTUS HAVE NOT BEEN, AND WILL NOT BE, REGISTERED UNDER THE UNITED STATES SECURITIES ACT OF 1933, AS AMENDED (THE ‘‘SECURITIES ACT’’) OR WITH ANY SECURITIES REGULATORY AUTHORITY OF ANY STATE OR OTHER JURISDICTION OF THE UNITED STATES AND MAY NOT BE OFFERED OR SOLD WITHIN THE UNITED STATES EXCEPT PURSUANT TO AN EXEMPTION FROM, OR IN TRANSACTIONS NOT SUBJECT TO, THE REGISTRATION REQUIREMENTS OF THE SECURITIES ACT. THE SHARES ARE BEING OFFERED AND SOLD OUTSIDE THE UNITED STATES IN RELIANCE ON REGULATION S UNDER THE US SECURITIES ACT.

    The Prospectus may be accessed in the United Kingdom only by persons who have professional experience in matters relating to investments falling within Article 19(5) of the Financial Services and Markets Act 2000 (Financial Promotion) Order 2005 and to persons to whom it may otherwise be lawful to communicate it to.

    By clicking on the appropriate button below, you will be deemed to have acknowledged and represented that you are not in the United States and are otherwise eligible to view the Prospectus. Otherwise you will be returned to the previous page.

    I AM accessing this website from the United States (as defined in Regulation S under the US Securities Act of 1933).

    I AM NOT accessing this website from the United States (as defined in Regulation S under the US Securities Act of 1933), but I AM NOT eligible to view the Prospectus pursuant to the restrictions described above.

    I AM NOTaccessing this website from the United States (as defined in Regulation S under the US Securities Act of 1933), and I AM otherwise eligible to view the Prospectus.